Quart size GatorGlide G2, G4, GB, FR up to 45 sq ft
We now Offer quart sizes that some of the small Boats, Canoes and layout boat owners may find more economical. Also good for the occasional touch upon the bigger boats.
Roll or spray GatorGlide G2 for a 3 to 4 mil dry or 6 to 8 wet mil coating. Roll or spray in two or three increments to avoid sagging if a heavier deposit is required. Apply the last coat as a thin 2 to 3 mil dry coating to obtain the best smoothness and abrasion resistance. If poor wetting occurs while applying GatorGlide coatings, then lightly roughen the dry GatorGlide surface with 400 grit sandpaper prior to top-coating. Make sure the surface temperature is above 40°F and the relative humidity is below 90% before coating. Allow at least 48 hours and ideally one week of curing before putting into service. Post heating at elevated temperatures will speed up curing and improve the abrasion resistance. Do not use harsh chemicals for cleaning GatorGlide surfaces, a simple hand wipe or a light scrape is adequate for removing marine growth. If the GatorGlide surface has become damaged or has
excessive wear, then an occasional touch up may be required. This can be achieved by simply rolling or spraying 1 to 3 mils of the GatorGlide G2 over the existing GatorGlide surface and allowing it to cure for at least 24 hours prior to putting it back in service.
After sanding with 100 – 150 grit and wiping thoroughly with acetone. New aluminum I recommend degreasing with a degreasing agent. I advise applying the slick bottom in multiple thin coats using a 6″ inch X 3/8″ to 1/2″ nap roller (see pic below) I also like working out of a 2 gal bucket with a 1 gal paint grid. See mixing video.
Five coats are ideal, First mix part “A” thoroughly with a high shear mixer or by shacking vigorously . Then you can mix as much as you can use in an hour. (Example: if you are using 1/4 of Part “A” then use 1/4 of Part “B”). When you open the bucket mark the outside at the top level then mark half, quarter and so on, do the same with the catalyst (part B)
The drying time between coats will vary depending on humidity but typically takes 20-30 minutes between coats. Throw your roller in the pot and throw a rag over it between coat (Do Not apply at night or while it raining even in your shop.) This is a water born product and needs to dry between coats. You have about a 60 min pot life, so mix accordingly.
GatorGlide will fish eye or separate when you are applying the first coat. It’s going to fisheye like you’re painting a waxed hood. That’s just how it is, after you roll the second section and before dipping your roller for the third go back and dry-roll the first section with the same roller. Do this on each coat. You will see it start to tighten up; This is completely normal! It will tighten up on the second and third coat. I know it looks weird but it’s how the stuff works. Depending on how porous the surface is will determine how much it fisheyes. Wait for it to dry (about 20-30 min) to the touch and start your next coat. “THIN TO WIN” I can’t stress this enough THIN COATS if you can put the same amount on in 3 coats or 5 coats go 5 it will be a better job. All coats should be done back to back so the integrate. Takes two hrs. to complete the job!
Do Not apply at night, in direct sunlight or while raining. You will lose performance!
Please never hesitate to call me to discuss the application, mixing tips or if you just want to bounce idea off of me. The longer it sits before you run it the harder it gets.
We ship most of all orders within two business day from the date received. Most orders in the 48 states are received by our customers in 5 to 7 business days via standard delivery. ALL PROCESSING AND DELIVERY TIMES ARE BASED ON BUSINESS DAYS, THIS EXCLUDES WEEKENDS AND HOLIDAYS.
|Dimensions||5 × 5 × 10 in|
Black, Blue, Graphite, Marsh Mud, Olive Green, Green, Orange, Slate, Yellow, White, Anchor
|G2, G4, GB or FR||
G2, G4, GatorBase, Fouling Base